Os-engines FS-26S-CX Manual de usuario

It is of vital importance, before attempting to operate your engine, to read the general 'SAFETY INSTRUCTIONS AND WARNINGS' section on pages

REPLACEMENT OF ELEMENTSIt is advisable to replace the upper filter element with a new one after not more than one hour of running time. It is not nece

GLOWPLUGThe role of the glowplugGlowplug lifeParticularly in the case of very high performance engines, glowplugs must be regarded as expendable items

TOOLS, ACCESSORIES, etc.The following items are necessary for operating the engine.Model engine fuel is poisonous. Do not allow it to come into contac

LONG SOCKET WRENCHRecommended for easy removal and replacement of the angled and recessed glowplug, the O.S.Long Socket Wrench incorporates a special

In the interests of a long working life and high performance, every internal-combustion engine needs to be "run-in" (or "broken-in"

1.5mm Turn the needle-valve gently clockwise until it stops. Do not use force to turn the needle beyond this point. Now reopen it 2 turns.Set the thr

It is vitally important to set the throttle at the correct position before attempting to start the engine. If the engine is allowed to run with the th

30˚20˚~30˚30˚30˚For 26S-CXNeedle SlotThe position of the needle-valve when starting the engine.Close the needle-valveapprox. 30° after running the veh

Note:Valve clearances of all O.S. four-stroke-cycle engines must be checked and reset ONLY WHEN THE ENGINE IS COLD. Procedure is as follows.Remove the

Note:If the gap is found to be less than 0.04mm, it is not necessary to readjust the clearance if the engine has good compression and starts easily. E

2~567891011~121213~16202127~281619~20SAFETY INSTRUCTIONS AND WARNINGS ABOUT YOUR O.S. ENGINEBASIC ENGINE PARTSENGINE INSTALLATIONAIR CLEANER TYPE 101N

Re-tighten locknut while holding adjusting screw stationary. (Fig.5.)4.Hold at the screw head.Fig.5Tighten Locknut.Remove 0.04mm feeler, rotate the cr

When cleaning the exterior of the engine, use methanol or kerosene. Do not use gasoline or any solvent that might damage the silicone fuel tubing.● PA

RACING ENGINE PARTS (72103020)(72103310)(71521000) (44125100) GENUINE PARTS & ACCESSORIEST-1020Tuned SilencerSuper Joint Tube 15 Long Socket Wr

-09C.M2.6X70-1--1--28N.+M3.5X5C.M2.6X18C.M2.6X12C.M2.6X7C.M2.6X7\asdfytrewq=743215-45-35-24-14-23-23-156a-1a-2[a-25-1iuop]u-1C…Cap Screw B…Binding He

Specifications are subject to alteration for improvement without notice.7 1615 0092 3210 0074 5231 0004 5264 0002 4881 8244 4166 1104 4166 1004 4166 0

-09C.M2.6X70-1--1--28N.+M3.5X5C.M2.6X18C.M2.6X12C.M2.6X7C.M2.6X7\asfytrewq=743215-45-35-24-14-23-23-156[5-1iuop]y-1y-2o-1d-1dd-2d-2ghFS-26S-CX EXPLODE

7 1615 0092 3210 0074 5231 0004 5264 0002 4881 8244 4166 1104 4166 1004 4166 0004 5701 1104 5762 0104 5762 100i4 4101 020u2 2630 0024 5702 100y4 4102

5-155-2765-34321-11N.+M3X6N.+M3.5X572 3081 706 62 1015 0012 1111 3005-35-22 1181 9765-152 1181 90242 1381 13032 2081 81122 1781 2001-1 2 2081 31312 20

2932.814UNF1/4-28433670.484.639.818FS-26S-C THREE VIEW DRAWING4.41cc (0.269cu.in.)18.5mm (0.728in.)16.4mm (0.648in.)2,000~22,000r.p.m.0.5bhp/17,000r.p

36431435.239.870.42020UNF1/4-28FS-26S-CX THREE VIEW DRAWINGDimension(mm)DisplacementBoreStrokePractical R.P.M.Power outputWeight4.41cc (0.269cu.in.)18

Remember that your engine is not a "toy", but a highly efficient internal-combustion machine whose power is capable of harming you, or other

C Copyright 2000 by O.S.Engines Mfg. Co., Ltd. All rights reserved. Printed in Japan.UNEQUALLEDQUALITYPRECISION&PERFORMANCEESTABLISHINGTHESTANDAR

WARNINGSModel engine fuel is poi-sonous. Do not allow it to come into contact with the eyes or mouth. Always store it in a clearly marked container an

This engine is intended for model cars. Do not attempt to use it for any other purpose.Mount the engine in your model securely, following the manufact

NOTESTo stop the engine, fully retard the throttle stick and trim lever on the transmitter, or, in an emergency, cut off the fuel supply by pinching t

These are overhead-valve four-stroke-cycle engines designed for 1/10 scale radio-controlled model cars. They are based on the latest version of the we

INSTALLING THE GLOWPLUGInstall the washer on the glowplug and insert carefully into cylinder-head, making sure that it is not cross-threaded before ti

AIR CLEANER TYPE 101This is a heavy-duty wet type air cleaner that has been developed specifically for O.S. model car engines. It contains specially i