Os-engines FS-40S-CX Manual de usuario

It is of vital importance, before attempting to operate your engine, to read the general 'SAFETY INSTRUCTIONS AND WARNINGS' section on pages

◆NOTES CONCERNING THE RECOIL STARTER( FS-40S-CX ONLY)REMINDER!◆◆Do not attempt to disassemble the recoil starter. If you do so, the very strong spring

GLOWPLUGThe role of the glowplugGlowplug lifeParticularly in the case of very high performance engines, glowplugs must be regarded as expendable items

TOOLS, ACCESSORIES, etc.The following items are necessary for operating the engine.FUELUse only top quality methanol-based model engine fuel.For consi

LONG SOCKET WRENCHRecommended for easy removal and replacement of the angled and recessed glowplug, the O.S.Long Socket Wrench incorporates a special

In the interests of a long working life and high performance, every internal-combustion engine needs to be "run-in" (or "broken-in"

2mmTurn the needle-valve gently clockwise until it stops. Do not use force to turn the needle beyond this point. Now reopen it 1 3/4 turns.Set the th

It is vitally important to set the throttle at the correct position before attempting to start the engine. If the engine is allowed to run with the th

30°10°~20°30°30°Needle SlotThe position of the needle-valve when starting the engine.Close the needle-valveapprox. 30° after running the vehicle for o

Note:Valve clearances of all O.S. four-stroke-cycle engines must be checked and reset ONLY WHEN THE ENGINE IS COLD. Procedure is as follows.• Feeler g

Note:If the gap is found to be less than 0.04mm, it is not necessary to readjust the clearance if the engine has good compression and starts easily. E

SAFETY INSTRUCTIONS AND WARNINGS ABOUT YOUR O.S. ENGINEINTRODUCTION, BASIC ENGINE PARTSINSTALLATION OF THE CARBURETORENGINE INSTALLATIONSUPER AIR CLEA

Re-tighten locknut while holding adjusting screw stationary. (Fig.5.)4.Hold at the screw head.Fig.5Tighten Locknut.Remove 0.04mm feeler, rotate the cr

When cleaning the exterior of the engine, use methanol or kerosene. Do not use gasoline or any solvent that might damage the silicone fuel tubing.● PA

(72103310)(71521000)RACING ENGINE PARTS(72200060)(45226200)(72403120)(71615009)(72403202) FOR FS-40S-C/CX(73300305)(73301012)(72403212)GENUINE PARTS &

iuytrewq=-0984321op[]\asd5-35-25-14-24-13-23-157f5-46(C.M3X12)C.M3X18C.M2.6X12C.M2.6X8C.M3X8C.M2.6X78-1[s-1s-2s-2gM3.5C…Cap Screw B…Binding Head Scre

Specifications are subject to alteration for improvement without notice.DescriptionCode No.Screw SetRocker CoverRocker Support Assembly Rocker Su

iuytrewq=-0984321op[]\asd5-35-25-14-24-13-23-157f5-46(C.M3X12)C.M3X18C.M2.6X12C.M2.6X8M.M2.6X7C.M2.6X78-1f-2gM3.5C.M3X8u-1u-2\f-1f-2hjC…Cap Screw B…B

Specifications are subject to alteration for improvement without notice.iDescriptionCode No.Screw SetRocker CoverRocker Support Assembly Rocker S

C…Cap Screw M…Oval Fillister-head Screw F…Flat Head ScrewN…Round Head Screw S…Set ScrewCARBURETTOR EXPLODED VIEW & PARTS LISTSpecifications ar

FS-40S-C THREE VIEW DRAWING6.49cc (0.396cu.in.)21.2mm (0.835in.)18.4mm (0.724in.)3,000~21,000r.p.m.0.9bhp/17,500r.p.m.323.5g (11.41oz.)Dimension(mm)Sp

FS-40S-CX THREE VIEW DRAWINGDimension(mm)DisplacementBoreStrokePractical R.P.M.Power outputWeightSpecification17.538.9424950UNF1/4-28202080.56.49cc (0

Remember that your engine is not a "toy", but a highly efficient internal-combustion machine whose power is capable of harming you, or other

C Copyright 2000 by O.S.Engines Mfg. Co., Ltd. All rights reserved. Printed in Japan.040101TEL. (06) 6702-0225FAX. (06) 6704-27226-15 3-Chome Imagawa

WARNINGSModel engine fuel is poisonous. Do not allow it to come into contact with the eyes or mouth. Always store it in a clearly marked container a

This engine is intended for model cars. Do not attempt to use it for any other purpose.Mount the engine in your model securely, following the manufact

NOTESTo stop the engine, fully retard the throttle stick and trim lever on the trans-mitter, or, in an emergency, cut off the fuel supply by pinching

These are overhead-valve four-stroke-cycle engines designed for 1/8 scale radio-controlled model cars. The engine is distinguished by a black-anodized

ENGINE INSTALLATIONMake sure that the vehicle's engine mounting surfaces are level and in the same plane. Poor installation may cause distortion

AIR CLEANER TYPE 102SINSTALLATION OF AIR CLEANERCarefully clean the carburettor, removing any old adhesive or sealant that may have been previously us