Os-engines FS-30S Manual de usuario

It is of vital importance, before attempting to operate your engine, to read the general 'SAFETY INSTRUCTIONS AND WARNINGS' section on pages

18Check that the throttle is one-third open from the fully closed position. Bring the starter into contact with the spinner nut or spinner and depress

20On starting from cold, with the needle-valveset at the rich starting position:Take note of this position of the needle-valve.This will produce the p

22These engines are equipped with a throttle type car-buretor which provides a wide range of engine speed control. With the throttle lever linked to a

23Start the engine.Make sure that the throttle isfully open.Adjust the neede-valve.Close the throttle gradually.Find the idling position.Fix the idlin

25123SymptomFactorCauseCorrective actionRecharge the electric starter battery.Recharge lead-acid cell or replace dry battery. (Note: An unused, or alm

27VALVE ADJUSTINGALL O.S. four-stroke engines have their valve(tappet) clearances correctly set before they leave the factory. However, if, after many

293.Fig.4Insert 0.04mm feeler gauge between valve stem and rocker-arm and gently turn adjusting screw clockwise until it stops.(Fig.4.)0.04mm FeelerGa

31Radial Mount SetO.S.Glow Plug TYPE FPropeller Locknut SetValve Adjusting Tool KitFlexible Exhaust PipesSuper Filter (L)NON-BUBBLE WeightLong Socket

32(C.M3x10)C.M2.6x12C.M2.6x7C.M2.6x7C.M2.6x18223-233-13-244-14-255-45-35-25-167891101112131415161716-1181920212223-123-22324252627FS-30S ENGINE EXPLOD

354522501045225000232100072320900345208010452310004526400024881824452661124526610245266010452011104526201045231100452010402263000245202010457710004520

2Remember that your engine is not a "toy", but a highly efficient internal-combustion machine whose power is capable of harming you, or othe

36S.M3X3N.+M3x6M2.6X5C.M2.6x711-1245366-276-46-36-1TYPE 20NCARBURETOR EXPLODED VIEW & PARTS LISTType of screw C...Cap Screw M...Oval Fillister-H

3814UNF1/4-28364- 3.371.5153747287511229444.89 cc (0.299 cu.in.)19.5mm (0.767 in.)16.4mm (0.648 in.)2,500-13,000 r.p.m.0.5ps / 10,000 r.p.m.279g (9.

40MEMO080203TEL. (06) 6702-0225FAX. (06) 6704-27226-15 3-Chome Imagawa Higashisumiyoshi-ku Osaka 546-0003, Japan C Copyright 2002 by

4NOTESThis engine was designed for model aircraft. Do not attempt to use it for any other purpose.Mount the engine in your model securely, following t

6NOTESAdjust the throttle linkage so that the engine stops when the throttle stick and trim lever on the transmitter are fully retarded. Alternatively

8INSTALLATIONHow to fasten the mounting screws.Hardwood mounting beamsO.S. radial motor mount(cast aluminum)Tighten second nut firmlydown onto first n

10SILENCERInstallation for FS-30S and FS-40SScrew the exhaust header pipe into the exhaust port until it "bottoms", then unscrew it just suf

12Fuel Can Filter311 Silicone tubingThis is required for the connection between the fuel tank and engine.10 Fuel can filterInstall a filter in the out

14Trainer & ScaleSport & AerobaticGLOWPLUGThe FS-30S and FS-40S are supplied with an O.S. Type F glowplug, specially designed for O.S. four-st

16CloseOpen4 Opening and closing of the needle-valveTurn needle-valve clockwise to close (for leaner mixture).Turn needle-valve counter-clockwise to